Hi Friends,

My sole purpose to start this forum is to unite all TUV 300 owners to share their experience no matter good or bad, to benefit others and bring niggles till Mahindra officials.

Please share your thoughts and publicize this forum to make our voice stand tall.

Thanks,
VP

pulling issue

Mileage, NVH, Batteries, Tyres and anything thats TECHNICAL!
harikrishnan
Newbie TUVian
Posts: 70
Joined: 01 Jun 2016, 19:28
Location: coimbatore
TUV 300 Varient: T8
Status: Offline

pulling issue

Postby harikrishnan » 17 Aug 2016, 22:44

hi all,

i have been facing continuous pulling issue on my TUV 300.i HAVE VISITED so manay times and till now no positive result.So many time cheAKED with MASS.Any body facing similar left side pulling issue problem.

Sharadkt
Senior TUVian
Posts: 296
Joined: 03 Apr 2016, 21:59
Location: Mumbai
TUV 300 Varient: T8 AMT
Status: Offline

Re: RE: pulling issue

Postby Sharadkt » 17 Aug 2016, 22:55

harikrishnan wrote:hi all,

i have been facing continuous pulling issue on my TUV 300.i HAVE VISITED so manay times and till now no positive result.So many time cheAKED with MASS.Any body facing similar left side pulling issue problem.

Did you visit some good tyre shop to check on wheel alignment?

Sent from my D6603 using Tapatalk

harikrishnan
Newbie TUVian
Posts: 70
Joined: 01 Jun 2016, 19:28
Location: coimbatore
TUV 300 Varient: T8
Status: Offline

Re: pulling issue

Postby harikrishnan » 31 Oct 2016, 23:31

Yet to check out side.n ext week I am planning for the same : :...

Akramkhan
Newbie TUVian
Posts: 24
Joined: 25 May 2016, 11:35
Location: Bhubaneswar
TUV 300 Varient: T8
Status: Offline

Re: pulling issue

Postby Akramkhan » 05 Nov 2016, 17:18

harikrishnan wrote:hi all,

i have been facing continuous pulling issue on my TUV 300.i HAVE VISITED so manay times and till now no positive result.So many time cheAKED with MASS.Any body facing similar left side pulling issue problem.


Hi

The Alignment at the Mahindra work shop is of no use. Just visit any other alignment center and the job will be done. before getting the alignment done please make sure the alignment center do have the TUV300 alignment figure from M&M. i just got it done and the result is very good :)
Regards,
Akram

clamfrog82
Newbie TUVian
Posts: 21
Joined: 29 Oct 2016, 12:48
Location: Bangalore
Status: Offline

Re: pulling issue

Postby clamfrog82 » 09 Nov 2016, 16:43

The best thing to do is to get the alignment done by a good alignment center which has computerized alignment system and which has the TUV300 alignment figures.

Bhushan27
Newbie TUVian
Posts: 34
Joined: 12 Apr 2017, 22:09
Location: Vasai
TUV 300 Varient: T8
Status: Offline

Re: pulling issue

Postby Bhushan27 » 15 Apr 2017, 23:04

I have done an alignment job for an alignment centre in my area which had the computerized TUV 300 setting. But even after that, there is slight pull to the left. Any suggestions please.?


Return to “Technical”

Who is online

Users browsing this forum: No registered users and 1 guest